Independent Local Providers Nationwide Coverage
(315) 640-3590

What a Hot Tub Needs at the New House: Pad, Deck and HOA

A level, continuous base that carries the tub full rather than empty, a permitted circuit, and in an HOA community the association's approval: Hot Spring's Grandee weighs 790 pounds dry but 5,810 pounds filled and occupied, about 92 pounds per square foot, while the standard prescriptive deck guide is sized for a 40 pound live load.

Moving a tub to a new house? Tell us what the new spot already has, and we line up an independent local spa mover. The quote is free.

What the new spot needs, in the order it usually happens

  1. HOA approval

    Architectural committee

    In an HOA community, first. Get the association's answer before you pay for a pad or a permit.

  2. Base

    Concrete contractor or structural engineer

    Level, continuous, and rated for the tub full. A prescriptive deck is sized for a 40 pound per square foot live load.

  3. Permit and circuit

    Licensed electrician

    A GFCI-protected circuit with a disconnect in sight of the tub, inspected before the tub arrives.

  4. Placement

    Spa mover

    Last, once there is somewhere for the tub to go.

A filled Hot Spring Grandee loads about 92 pounds per square foot. Hot Spring; American Wood Council DCA 6.

The weight that matters is the full one

Everyone plans for the weight of the tub on moving day. The base has to carry it on every day after that. Hot Spring lists its Grandee at 790 pounds dry and 5,810 pounds filled, counting 455 gallons of water and a 175 pound adult in every seat. Water weighs about 8.3 pounds a gallon, according to the U.S. Geological Survey, which is why the number jumps. Spread over the Grandee's 8 foot 4 inch by 7 foot 7 inch footprint, the filled weight works out to about 92 pounds per square foot, and Arctic Spas' manual asks for balconies, concrete pads and decks able to support at least 146.

Is your deck strong enough?

Probably not as built, unless it was built for a tub. The American Wood Council's prescriptive deck guide, DCA 6, sizes decks for a 40 pound per square foot live load and a 10 pound dead load, and says concentrated loads such as hot tubs are beyond its scope. Your building department may want an engineer's stamped letter confirming the deck can take the extra load of a hot tub on an elevated platform, so ask what it requires. The person who answers this question is a structural engineer, not a mover.

What a ground-level pad needs

On the ground the rule is level and continuous. Resort Hot Tubs' warranty requires a uniformly firm, continuous and level surface, recommends a concrete pad at least 4 inches thick with steel reinforcing bars, and excludes damage from failing to provide even support. Arctic Spas treats damage from insufficiently prepared or uneven ground as abuse, and asks for at least 24 inches of access around the spa for service. If the pad or the trench for the new circuit means digging, call 811 before any digging starts.

Where on the lot it is allowed to sit

The spot you picked has to pass the town, not just the eye. Your town may set a minimum distance from property lines, and may ask for a boundary survey or a scaled site plan showing distances to lot lines and structures. Your local building department will specify the setback and survey requirements. Ask your building department about overhead wires, nearby glass, and whether a barrier or lockable safety cover is required. The electrical code adds its own spacing: the disconnect has to sit within sight of the tub and at least 5 feet from it.

HOA rules

In deed-restricted communities the HOA can decide the spot before the town does. HOA guidelines may limit hot tub dimensions, require rear yard placement, set their own setback distances, and require screening from neighbors. Architectural committee approval may be required. Your HOA governing documents will specify size limits and placement rules. If your property is in an HOA community, get the association's answer before you contact the town.

When the spot is ready, and when you do not need a mover yet

If the new house already has a level pad and a spa circuit with GFCI protection, and the tub fits the HOA's limits, the move may be the only job left. If it has none of those, you do not need a mover yet. You need the HOA's answer, the pad poured or the deck checked by an engineer, and the electrician's permit and circuit, and the move goes last. Tell us what the new spot has today and we will tell you which of those is still outstanding, then connect you with an independent local spa mover, once there is somewhere for the tub to go.

Sources

Key facts and standards used in this guide

Hot Spring lists its Grandee hot tub at 8 feet 4 inches by 7 feet 7 inches by 38 inches, holding 455 gallons, with a dry weight of 790 pounds and a filled weight of 5,810 pounds including water and a 175 pound adult in every seat.

Source: Hot Spring Spas, accessed 2026-09-22

The U.S. Geological Survey lists water at 70F as weighing 62.3 pounds per cubic foot, which is about 8.3 pounds per U.S. gallon.

Source: U.S. Geological Survey, Water Science School, accessed 2026-09-22

Spread over its 8 foot 4 inch by 7 foot 7 inch footprint, Hot Spring's published 5,810 pound filled weight for the Grandee works out to about 92 pounds per square foot.

Source: Hot Spring Spas, accessed 2026-09-22

Arctic Spas' owner's manual states that balconies, concrete pads and decks should be built to code and be able to support at least 146 pounds per square foot, and that the customer must provide at least 24 inches of access all around the spa for service.

Source: Arctic Spas, Owner's Manual (International), accessed 2026-09-22

The American Wood Council's prescriptive deck guide, DCA 6, sizes its members for a 40 pound per square foot live load and 10 pound dead load, and states that concentrated loads such as hot tubs are beyond its scope.

Source: American Wood Council, DCA 6 Prescriptive Residential Wood Deck Construction Guide, accessed 2026-09-22

Resort Hot Tubs' warranty requires the spa to sit on a uniformly firm, continuous and level surface, recommends a concrete pad at least 4 inches thick with steel reinforcing bars, and excludes damage from failing to provide even, proper support.

Source: Resort Hot Tubs, accessed 2026-09-22

Arctic Spas' warranty treats any damage caused by moving the spa, or by improper installation including insufficiently prepared or uneven ground, as abuse, and states that its warranties terminate on transfer of ownership from the original customer.

Source: Arctic Spas, accessed 2026-09-22

National Electrical Code section 680.13 requires a maintenance disconnect for spa and hot tub equipment that is readily accessible, within sight of the equipment and at least 5 feet horizontally from the inside walls of the spa or hot tub, unless a permanent barrier creates a reach path of 5 feet or more.

Source: National Electrical Code, Article 680 (NEC 2017 edition; the adopted edition varies by state), accessed 2026-09-22

National Electrical Code section 680.44 requires the outlet supplying a self-contained or packaged spa or hot tub to be protected by a ground-fault circuit interrupter, unless a listed unit is marked as having integral GFCI protection.

Source: National Electrical Code, Article 680 (NEC 2017 edition; the adopted edition varies by state), accessed 2026-09-22

Next Step

Ready to plan your move?

Tell us where the tub is and where it is going. We line up a local spa mover and you get a free quote.

Get Quote Call (315) 640-3590